Need help? Our customer service team is ready to assist!

1.844.640.3813

Support Center

VLR-6 RESISTOR + WP DUOTAP HARNESS

Rating:
98% of 100
SKU
VLR_6_DUO_WP
$15.00 EACH
In Stock
YEAR WARRANTY
DESIGNED IN USA

Exclusive The VLR Pro is by far the cleanest and safest way to add load to any vehicle lighting system. VLR Pro resistors accomplish the same task as a common gold resistor but are easier to install, have a lower profile, and run 50% cooler (250°F MAX).

One for One We get asked all the time, how many resistors will I need? The answer is simple: If you're removing a filament turn signal bulb add one VLR-6 in its place. It's like balancing a scale, if you remove weight the scale will be unbalanced so you're simply putting the same amount of weight (load) back on.

Construction Using a wire wound resistor potted inside of a black anodized aluminum heat sink, these are the most weatherproof and thermally safe resistors on the market. VLR Pro resistors use high temp silicone wiring attached to a male waterproof circular connector.

Mounting The supplied VLR High Temp mounting tape can be used to adhere the resistor body to a flat clean metal surface on the vehicle. As an extra precaution: VLR Pro resistors should be mounted out of harms way and should not touch any plastic or other wiring.

For exterior applications we recommend filling the DuoTap with our dielectric grease.

TECHNICAL SPECS

Current Draw: 1.9A @ 12V | 2.25A @ 14.4V
Load = 1 standard filament bulb (equivalent wattage: 25W)

Learn more about adding load to your lighting system HERE.

Plug N' Play Install the inline adapter between factory bulb connector and new input connector (harness, LED, etc.).
Waterproof Fully potted and uses waterproof connectors
Mounting Can be installed with included high temp mounting tape or screws
Safer Temperature Max Temp = 250°F (121°C)
More Information
Current Draw @ 14.4V 2.25A
Operating Voltage 1-18V
Wire Type PVC 80° C
Finish Type Anodized
Dimensions 80mm x 40mm x 12mm
Material 6061 Aluminum
Wire Length 250mm (10")
Contact Material Gold Plated
Resistor Value 6 Ohm
Mounting High Temp Tape or Screws
Plug Connection Style 2 Pin Waterproof Plug (WP)
Electrical Connection Splice / Tap
Load Equivalent 1 Turn Signal Bulb
Temperature (Continuous) 250° F
Temperature (Momentary) 150° F

Fixing Hyperflash

One of the most common problems that arise when replacing stock filament bulbs with LEDs is bulb flashes fast, or you get bulb out warnings on the interior display. By design, most vehicles use either of these methods to tell the driver that a bulb somewhere on the car has burned out.

How does the car know there is a bulb out?

The flasher unit, module, or computer controls when to double the flash rate or display a bulb out warning. It is designed to monitor the current draw or load on the turn signal circuit. It monitors the vehicle's left/right circuit, and on some advanced systems, it monitors all 4 bulbs independently.

How do you prevent the turn signals from hyperflashing?

The solution is to either replace the flasher unit with our electronic LED flashers (if replaceable) or add enough load back on the system to replace the missing load. Correcting hyperflash or bulb out warnings when you upgrade to LEDs is relatively easy once you understand what needs to be done.

 

ONE VLR-6 RESISTOR = ONE 25W BULB

We get asked all the time, how many resistors will I need, or what size resistor do I need? The answer is simple: If you're replacing a 20W to 25W filament turn signal bulb install one VLR-6 in its place. It's like balancing a scale, if you have 2lbs on each side and remove 2lbs from one side the scale will tip so you're simply putting the same amount of weight (load) back on the side you removed it from.

Once you have purchased the VLR-6, installing them is quite simple. The resistors need to be tapped to the positive and negative turn signal wires with the DuoTap harness. If you are using our V6 Triton system the resistors are plug and play.

Mounting the VLR is extremely easy with the supplied high-temperature double-sided tape. Just peal and stick them to a clean metal surface. Always keep your resistor away from existing wiring or plastic parts as they could be damaged with sustained resistor use.

Once the resistors have been installed test them by turning on the turn signals. Hazards will not hyperflash so be sure to test each side individually.

CAUTION - LOAD RESISTORS MAY GET HOT

Even though the VLR resistors operate much cooler than standard gold resistors they can still get hot especially if the turn signals are left on for an extended period of time (i.e. hazards are on while broken down alongside the road). It is a good idea to always mount a load resistor to a metal surface away from other wires or plastic parts.

LOAD SPECIFICATIONS FOR ALL VLR RESISTORS

VLR-3 4.5A @14.4V
VLR-6 2.25A @14.4V
VLR-10 1.3A @14.4V
VLR-15 1.0A @14.4V
VLR-25 0.55A @14.4V

 

STILL NEED HELP?

CONTACT US

1x VLR-6 Resistor
1x DuoTap Harness
1x 3M Mounting Tape

Why VLEDS?

There are a ton of online retailers selling standard off the shelf LED products of all kinds. There are so many options that it gets overwhelming.

Here are the 10 reasons why you can trust us with your LED lighting needs.

1. Our brand

We design and develop our products inhouse. We are not a traditional reseller. We employ in-house designers, mechanical engineers, and electrical engineers. Fitment, color, performance, and reliability are essential and allows us to provide you with the best products possible.

2. We're an established company that isn't going anywhere

We've been in business for over 16 years and have built an excellent reputation among automotive lighting enthusiasts. We are trusted and recommended by car and truck guys all over the world.

3. Excellent customer service and technical support

We pride ourselves in offering first-class support to our customers. When you call or email us, you're talking to a person with years of knowledge and experience in the industry.

4. 25+ years of combined experience

Our staff is extremely knowledgeable and works firsthand with our products, from concept to installation. They know the ins and outs of every product we sell.

5. Low-cost, flat rate shipping with same-day order processing and full visibility tracking.

We have a fast and efficient pick and pack system in place with barcode scanning. Your order will be accurate and well packaged for safe delivery to your door. Our shipping team provides you with order communication every step of the way.

6. Easy returns

We offer a 30-day money-back guarantee. If you are not completely satisfied with any purchase, send the product back for a full refund.

7. Secure payments

We accept PayPal, Affirm and all major credit cards.

8. Great warranty with fast replacements

In most cases, you are not required to ship back your defective item. See details here.

9. Largest selection of LED products and replacement bulbs

We make an LED replacement for nearly every bulb on your vehicle. In many categories, we have several options and price points to meet your needs. Everyone has different tastes in color, so we offer up to 3 different kelvin ratings in our white LEDs, whereas the other guys only offer one.

10. Easy to use website

Designed with the user in mind:

  • Simple navigation with a year make model bulb finder ensures you get the right part for your application
  • Clear and quality product photos so you know exactly what you're getting
  • Informational product descriptions
  • Specs and data on nearly every product
  • Install guides for the more complicated items
Write Your Own Review
Write a ReviewVLR-6 RESISTOR + WP DUOTAP HARNESS
To Top