Need help? Our customer service team is ready to assist!

1.844.640.3813

Support Center

400LM TOTAL

REAR FOOTWELL LED LIGHT KIT ADD-ON

SKU
REAR_FWK-C
As low as $45.00 $50.00 PER KIT
In Stock

YEAR WARRANTY
DESIGNED IN USA
Description

Add On Already have our front footwell kit? Adding light to the rear seats couldn't be easier! It's a simple plug-and-play installation using the output connector from the passenger-side light bar. The daisy chain wiring design allows multiple bars to be connected on one circuit, so you can add as many as you want! It only takes a few minutes, and the results are phenomenal!

Low Profile At just a little under 3" long and 1/4" thick, these ultra-slim light bars can be installed just about anywhere!

Highlights

  • Plug n Play wiring with our bulb base adapter
  • Made with a thick aluminum circuit board for better reliability and a longer lifespan.
  • Black PCB and aluminum housing adds a nice touch and blends better with most interior panels.
  • High-quality 3M VHB tape or Velcro. Just clean and prep any smooth or carpeted surface, peel and stick the strip light to install.
  • Built-in current limiting resistor and diode protects the strip from reversed polarity installation. If they don't light, flip the wires around.
  • No stripping or fussing with wires! Simply daisy chain them together using wire adapters and extensions. DuoTaps are recommended for hardwire installations.
  • Color-specific chips that match all other VLEDS LED bulbs.
WHAT COLOR TEMPERATURE SHOULD I GET?

Color temperature is primarily a style choice, but the human eye perceives a whiter light as brighter. The image below shows a side-by-side comparison of our three choices. We offer 5000K, 5500K, and 6000K color options. 5000K is natural white, 5500K is pure white, and 6000K is white with a tint of blue. Ultimately, it's up to you, depending on your lighting goals. The higher Kelvin number DOES NOT mean the output will be higher; it is quite the opposite. The higher you go on the Kelvin scale, the lower the output.

PRODUCT DIMENSIONS

Warranty

This product comes with a 3-year warranty supported by VLEDS. We do not require the product to be shipped back to us. Improper product installation, as well as any system components or wiring modifications, will void all warranties. See our full Warranty Details for more details.

What's Included

2X - 21 LED Bar Lights
1X - LSE VHB Tape for Smooth Surfaces
1X - Velcro Tape for Carpet
2X - 8 Foot Extension Wires
1X - 4 Foot Extension Wire
4X - Zip Ties

 

More Information
Instructions

TOYOTA TUNDRA REAR FOOTWELL KIT INSTALLATION

ESTIMATED TIME TO INSTALL 

  • 20-30 MINUTES
TOOLS REQUIRED 

  • WIRE CUTTERS
  • RUBBING ALCOHOL
  • RAG OR PAPER TOWELS
  • PRY TOOL OR FLAT-HEAD SCREWDRIVER
DOWNLOAD

INSTALLATION GUIDE

1. Remove the scuff plate from the front passenger side by firmly pulling upwards.

2. Remove the retaining nut or hardware from the kick panel and pull the panel straight back.

3. Remove the plastic retaining clip and re-install it on the kick panel.

4. Plug the 8ft extension wire into the passenger side bar light. Route the wire next to the factory wiring. Zip-tie the wire loosely for now.

5. Continue routing the wire down the sill plate channel.

6. Move the passenger seat to the forward position.

7. Route the wire under the carpet fold.

8. Route and tuck wiring through the elastic straps on each corner under the seat.

9. Plug in the passenger side bar light. Clean both surfaces, apply 3M tape for leather seats or velcro for cloth, and mount the bar light.

10. Tuck the wire under the carpet and route under the
seat rail. 

11. Start routing and tucking the wire along the center console and over towards the driver seat.

12. Route the wire under the carpet.

13. Bring the wire up next to the factory wiring harness and tape or zip tie to the harness.

14. Tuck the wire under the elastic, as shown in step 8. Clean the under-seat surface and mount the second light bar.

15. Confirm both seats move in the full range of motion without pulling the wires. Zip tie or tape any loose wiring. Enjoy your new rear footwell lights!

Note: The door circuit may time out during the installation. Close the driver-side door and open it again, or depress the door switch and release it.

© VLEDS INC.

Revision A | 1.14.22

Output (Each) 400LM TOTAL
Current Draw @ 14.4V 0.5A
Operating Voltage 12-18V
Light Source 3014 Proprietary Chip
Driver Style Resistors

TOYOTA TUNDRA REAR FOOTWELL KIT INSTALLATION

ESTIMATED TIME TO INSTALL 

  • 20-30 MINUTES
TOOLS REQUIRED 

  • WIRE CUTTERS
  • RUBBING ALCOHOL
  • RAG OR PAPER TOWELS
  • PRY TOOL OR FLAT-HEAD SCREWDRIVER
DOWNLOAD

INSTALLATION GUIDE

1. Remove the scuff plate from the front passenger side by firmly pulling upwards.

2. Remove the retaining nut or hardware from the kick panel and pull the panel straight back.

3. Remove the plastic retaining clip and re-install it on the kick panel.

4. Plug the 8ft extension wire into the passenger side bar light. Route the wire next to the factory wiring. Zip-tie the wire loosely for now.

5. Continue routing the wire down the sill plate channel.

6. Move the passenger seat to the forward position.

7. Route the wire under the carpet fold.

8. Route and tuck wiring through the elastic straps on each corner under the seat.

9. Plug in the passenger side bar light. Clean both surfaces, apply 3M tape for leather seats or velcro for cloth, and mount the bar light.

10. Tuck the wire under the carpet and route under the
seat rail. 

11. Start routing and tucking the wire along the center console and over towards the driver seat.

12. Route the wire under the carpet.

13. Bring the wire up next to the factory wiring harness and tape or zip tie to the harness.

14. Tuck the wire under the elastic, as shown in step 8. Clean the under-seat surface and mount the second light bar.

15. Confirm both seats move in the full range of motion without pulling the wires. Zip tie or tape any loose wiring. Enjoy your new rear footwell lights!

Note: The door circuit may time out during the installation. Close the driver-side door and open it again, or depress the door switch and release it.

© VLEDS INC.

Revision A | 1.14.22

Many online retailers sell standard off-the-shelf LED products, and the options can be overwhelming. Here are ten reasons you can trust us with your LED lighting needs.

1. Our brand
We design and develop our products in-house. We are not a traditional reseller. We employ designers, mechanical engineers, and electrical engineers. Fitment, color, performance, and reliability are essential, allowing us to provide you with the best products possible.

2. We're an established company that isn't going anywhere
We've been in business for 19 years and have built an excellent reputation among automotive lighting enthusiasts. We are trusted and recommended by car and truck guys worldwide.

3. Excellent customer service and technical support
We pride ourselves on offering first-class support to our customers. When you call or email us, you're talking to a person with years of knowledge and experience in the industry.

4. 25+ years of combined experience
Our staff is extremely knowledgeable and works firsthand with our products, from concept to installation. They know the ins and outs of every product we sell.

5. Low-cost, flat-rate shipping with same-day order processing and full visibility tracking.
We have a fast, efficient pick-and-pack system with barcode scanning. Your order will be accurate and well-packaged for safe delivery to your door. Our shipping team provides you with order communication every step of the way.

6. Secure payments
We accept PayPal, Affirm, and all major credit cards.
 
7. 60-day return
Life gets busy, so you've got time with our 60-day return policy.

8. Great warranty with fast replacements
In most cases, you are not required to ship back your defective item. See details here.

9. Largest selection of LED products and replacement bulbs
We make an LED replacement for nearly every bulb on your vehicle. We have several options and price points in many categories to meet your needs. Everyone has different tastes in color, so we offer up to 3 different kelvin ratings in our white LEDs, whereas the other guys only offer one.

10. Easy to use website
Designed with the user in mind:
 
  • Simple navigation with a year make model bulb finder ensures you get the right part for your application
  • Clear and quality product photos so you know exactly what you're getting
  • Informational product descriptions
  • Specs and data on nearly every product
  • Install guides for the more complicated items
Write Your Own Review
Write a ReviewREAR FOOTWELL LED LIGHT KIT ADD-ON
To Top